New Condo

1. Pipe material and sizingCritical

   Verify pipe material and sizes match approved plans

   FBC-P 604.1FBC-P 305.1
2. Burial depthCritical

   Verify underground pipe burial depth meets code minimum

   FBC-P 305.5
3. Pipe slope and supportCritical

   Verify proper slope on drain lines and adequate support

   FBC-P 704.1
4. Pressure testCritical

   Verify plumbing system holds required pressure test

   FBC-P 312.2
5. Cleanout locations

   Verify cleanout access points are installed per plans

   FBC-P 708.1

1. Conduit installationCritical

   Verify conduit material, size, and routing per plans

   NEC 300.5
2. Burial depthCritical

   Verify conduit burial depth meets code minimum

   NEC 300.5
3. UFER ground connectionCritical

   Verify UFER grounding electrode is properly connected to rebar in footing

   NEC 250.52(A)(3)
4. Conduit protection

   Verify conduit is protected from damage where exposed

   NEC 300.5(D)

1. Footing dimensionsCritical

   Verify footing width and depth match approved plans

   FBC-R R403.1FBC-R R403.1.1
2. Rebar size and spacingCritical

   Verify rebar size, spacing, and placement per plans

   FBC-R R403.1
3. UFER grounding electrodeCritical

   Verify minimum 20 feet of #4 bare copper or rebar is encased in footing

   NEC 250.52(A)(3)
4. Slab vapor barrierCritical

   Verify vapor barrier is installed under slab per plans

   FBC-R R506.2.3
5. Slab thickness and wire meshCritical

   Verify slab thickness and reinforcement per plans

   FBC-R R506.1
6. Foundation anchorage layout

   Verify anchor bolt placement for sill plate attachment

   FBC-R R403.1.6

1. Cell fill and groutCritical

   Verify cells are properly grouted per plans

   FBC-R R609.1.1
2. Tie beam reinforcementCritical

   Verify tie beam rebar size, spacing, and lap splices per plans

   FBC-R R609.1
3. Lintel reinforcementCritical

   Verify lintel rebar and sizing over openings per plans

   FBC-R R609.7
4. Vertical rebar placementCritical

   Verify vertical rebar is properly placed and spaced in block wall

   FBC-R R609.1

1. Wall stud spacing and sizeCritical

   Verify stud size and spacing match approved plans

   FBC-R R602.3FBC-R R602.3.1
2. Headers and beamsCritical

   Verify header and beam sizes over openings per plans

   FBC-R R602.7
3. Top and bottom plate connectionsCritical

   Verify double top plates with proper lapping and anchored bottom plates

   FBC-R R602.3.2
4. Corner and intersection bracingCritical

   Verify proper bracing at corners and wall intersections

   FBC-R R602.10
5. Window and door rough openingsCritical

   Verify rough openings match approved plans for size and location

   FBC-R R602.7
6. Hurricane straps and hold-downsCritical

   Verify hurricane straps and hold-down hardware installed per plans

   FBC-R R802.11
7. Fire blocking

   Verify fire blocking is installed at required locations

   FBC-R R602.8
8. Fire separation wall framingCritical

   Verify party/fire wall is framed continuously from foundation to underside of roof sheathing per plans

   FBC-R R302.1FBC-R R302.2
9. Draft stopping in party wallCritical

   Verify draft stopping is installed in concealed spaces of the fire separation wall

   FBC-R R302.4

1. Roof sheathing attachmentCritical

   Verify roof deck nailing pattern and edge spacing per the approved nailing schedule.

   FBC-R R803.2FBC-R R802.11
2. Roof sheathing material and thicknessCritical

   Verify roof sheathing panel material, thickness, and span rating match the approved plans.

   FBC-R R803.1
3. Panel gap spacing at roof deck

   Verify proper edge gap between roof sheathing panels per the panel manufacturer.

   FBC-R R803.2

1. Wall sheathing attachmentCritical

   Verify wall sheathing nailing pattern and edge spacing per the approved nailing schedule (shear wall zones often require tighter spacing).

   FBC-R R602.3
2. Wall sheathing material and thicknessCritical

   Verify wall sheathing panel material, thickness, and grade stamp match the approved plans.

   FBC-R R602.3
3. Panel gap spacing at walls

   Verify proper edge gap between wall sheathing panels per the panel manufacturer.

   FBC-R R602.3

1. Truss spacing and alignmentCritical

   Verify truss spacing and alignment match approved plans

   FBC-R R802.10
2. Truss-to-wall connectionCritical

   Verify hurricane clips or straps at every truss-to-wall connection

   FBC-R R802.11
3. Truss bracingCritical

   Verify lateral and diagonal bracing is installed per truss engineering

   FBC-R R802.10.3
4. Truss engineering on siteCritical

   Verify sealed truss engineering package is available and matches installed trusses

   FBC-R R802.10.1
5. Gable end bracing

   Verify gable end trusses are properly braced

   FBC-R R802.10.3

1. Underlayment installationCritical

   Verify roof underlayment is installed per code and manufacturer specs

   FBC-R R905.1.1
2. Drip edge installationCritical

   Verify drip edge is installed at eaves and rakes

   FBC-R R905.2.8.5
3. Valley and flashingCritical

   Verify valley flashing and wall flashing are properly installed

   FBC-R R903.2
4. Roof penetration sealing

   Verify all roof penetrations are properly sealed and flashed

   FBC-R R903.2

1. Supply pipe sizing and materialCritical

   Verify supply pipe sizes and material match approved plans

   FBC-P 604.1
2. DWV pipe sizing and slopeCritical

   Verify drain, waste, and vent pipe sizes and slope per plans

   FBC-P 704.1
3. Pipe support and hangingCritical

   Verify pipes are properly supported at required intervals

   FBC-P 308.1
4. Vent termination locations

   Verify vent pipes terminate properly through roof

   FBC-P 903.1
5. Water heater rough-in

   Verify water heater location, drain pan, and connections per plans

   FBC-P 607.1

1. Panel installationCritical

   Verify electrical panel is properly mounted and sized per plans

   NEC 408.4
2. Wire sizing per circuitsCritical

   Verify wire gauge matches breaker amperage for each circuit

   NEC 210.3NEC 240.4
3. Box fill and installationCritical

   Verify electrical boxes are properly installed and not overfilled

   NEC 314.16
4. GFCI and AFCI locationsCritical

   Verify GFCI and AFCI protection is provided where required

   NEC 210.8NEC 210.12
5. Smoke and CO alarm wiringCritical

   Verify interconnected smoke and CO alarm wiring is in place

   FBC-R R314.3FBC-R R315
6. Grounding and bondingCritical

   Verify grounding electrode system and bonding connections

   NEC 250.50

1. Ductwork installationCritical

   Verify duct sizes, routing, and support match approved plans

   FBC-M 603.1
2. Duct sealingCritical

   Verify duct joints and connections are properly sealed

   FBC-M 603.9
3. Equipment placementCritical

   Verify air handler and condenser locations per plans with required clearances

   FBC-M 304.1
4. Refrigerant line installation

   Verify refrigerant line sizing and insulation per plans

   FBC-M 1101.3
5. Return air pathway

   Verify return air pathways are properly sized and located

   FBC-M 601.2

1. Wall cavity insulation R-valueCritical

   Verify wall insulation R-value matches energy calculations

   FBC-E R402.1
2. Ceiling/attic insulation R-valueCritical

   Verify ceiling or attic insulation R-value per energy calculations

   FBC-E R402.1
3. Insulation coverage and gapsCritical

   Verify no gaps, voids, or compression in insulation installation

   FBC-E R402.4
4. Air sealing

   Verify air sealing at penetrations, top plates, and rim joists

   FBC-E R402.4.1

1. Wall covering material and installationCritical

   Verify exterior wall covering material matches approved plans and is properly installed

   FBC-R R703.1
2. Weather-resistive barrierCritical

   Verify weather-resistive barrier is properly installed behind cladding

   FBC-R R703.2
3. Flashing at penetrations and transitionsCritical

   Verify flashing is installed at windows, doors, and wall transitions

   FBC-R R703.4
4. Fastener pattern and spacing

   Verify cladding fastener type and spacing per manufacturer and plans

   FBC-R R703.1

Most jurisdictions skip this inspection for this project type. Confirm with your building department whether they'll require it.

1. Drywall thickness and typeCritical

   Verify drywall thickness matches plans, moisture-resistant board in wet areas

   FBC-R R702.3.1
2. Fastener spacingCritical

   Verify screw or nail spacing meets code requirements

   FBC-R R702.3.5
3. Fire-rated assembliesCritical

   Verify fire-rated walls and ceilings have proper drywall layers per rating

   FBC-R R302.6
4. Moisture barrier in wet areas

   Verify moisture barrier behind tub/shower surrounds where required

   FBC-R R702.4
5. Fire-rated party wall assemblyCritical

   Verify party wall has required layers of Type X gypsum per fire rating (typically 1-hour)

   FBC-R R302.1FBC-R R302.2
6. Party wall penetration firestoppingCritical

   Verify all penetrations through party wall are firestopped with approved materials

   FBC-R R302.4

1. Panel complete and labeledCritical

   Verify panel cover installed, all breakers labeled, no open knockouts

   NEC 408.4
2. GFCI and AFCI operationalCritical

   Verify all GFCI and AFCI devices test and reset properly

   NEC 210.8NEC 210.12
3. Receptacle and switch functionCritical

   Verify outlets and switches operate correctly throughout

   NEC 210.52
4. Light fixtures installed

   Verify all light fixtures are installed and operational

   NEC 210.70
5. Exterior lighting and outletsCritical

   Verify exterior outlets are GFCI protected and lighting is functional

   NEC 210.8NEC 210.52(E)

1. Fixture installation and operationCritical

   Verify all plumbing fixtures are installed, connected, and operational

   FBC-P 405.1
2. Water heater installationCritical

   Verify water heater is properly installed with TPR valve, drain pan, and discharge pipe

   FBC-P 607.1
3. No visible leaksCritical

   Verify no leaks at any supply or drain connection

   FBC-P 312.1
4. Hose bibbs and exterior plumbing

   Verify exterior hose bibbs have backflow prevention

   FBC-P 608.15.4.2

1. System operational testCritical

   Verify HVAC system starts, runs, and produces heated and cooled air

   FBC-M 304.1
2. Air handler and condenser installationCritical

   Verify equipment is properly installed with required clearances and level

   FBC-M 304.1
3. Condensate drainCritical

   Verify condensate drain is properly routed and terminated

   FBC-M 307.2
4. Duct registers and grilles

   Verify all supply and return registers are installed and operational

   FBC-M 601.2
5. Equipment labels and data plates

   Verify equipment nameplates match approved plans for capacity and efficiency

   FBC-M 304.1

1. Egress doors and hardwareCritical

   Verify egress doors provide minimum 32-inch clear width and proper hardware

   FBC-R R311.2
2. Smoke alarms installed and operationalCritical

   Verify smoke alarms in each bedroom, outside sleeping areas, and each level

   FBC-R R314.3
3. CO alarms installedCritical

   Verify carbon monoxide alarms where required

   FBC-R R315
4. Emergency escape openingsCritical

   Verify bedroom windows meet egress size requirements

   FBC-R R310.1
5. Stairway complianceCritical

   Verify stair rise, run, handrail height, and landing dimensions

   FBC-R R311.7
6. Party wall continuity and sealingCritical

   Verify fire separation wall is complete with no unsealed penetrations, gaps, or breaches from foundation to roof

   FBC-R R302.1FBC-R R302.2FBC-R R302.4
7. Address numbers visible

   Verify address numbers are posted and visible from street

   FBC-R R319.1
8. Exterior finishes complete

   Verify exterior cladding, trim, and weatherproofing are complete

   FBC-R R703.1
9. Site grading and drainage

   Verify finish grade slopes away from foundation minimum 6 inches in 10 feet

   FBC-R R401.3